UsProducts / Services

March & Martin is pleased to offer the following products and services:


Icynene Insulation:

ICYNENE LD-C-50® is the product that made the Icynene name synonymous with superior-quality spray foam insulation. It has been used in thousands of residential and commercial projects since 1986, consistently outperforming traditional insulation types.

  1. Approved for commercial building types I, II, III, IV, and V construction – unlike most open cell spray foams
  2. One-step insulation and air sealing
  3. Open-cell, low-density 0.5 lb.
  4. R-value = 3.7 per inch
  5. Soft, flexible composition
  6. <5% water absorption
  7. 100% water-blown, HFC- and PBDE-free

(link to product spec, MSDS, ESR)


ICYNENE LD-R-50® spray foam insulation is a revolutionary, renewable-based formula made using castor oil. This has many environmental and health-related advantages. LD-R-50 is a one-step performance material which both insulates and air seals a building for the lifetime of the structure. Icynene LD-R-50 is guaranteed to perform as specified for the life of the building.

  1. R-value = 3.7 per inch
  2. <5% water absorption
  3. Vapor permeable, support bi-directional drying of assemblies
  4. Soft, flexible composition maintains an air seal even after seasonal expansion/contraction of building assembly
  5. Open-cell structure with air, 100% water-blown, Light density 0.5 lb.
  6. HFC- and PBDE-free

(link to product spec, MSDS, ESR)


ICYNENE MD-C-200 is Icynene's leading closed-cell spray foam insulation product from the proven industry leader. It is air-impermeable with a built-in vapor retarder.

  1. Approved for commercial building types I, II, III, IV, and V construction
  2. One-step insulation and air sealing
  3. Closed-cell, medium-density 2.0 lb.
  4. R-value = 6.5 per inch
  5. Rigid, not flexible composition
  6. Rejects bulk water
  7. HFC-and PBDE-free

(link to product spec, MSDS, ESR)


Traditional Closed Cell Polyurethane Spray Foams:

Non-Icynene Closed Cell Foam March and Martin offers several different manufacturer’s products for chemically blown, closed-cell, 2-lb spray-applied polyurethane foam.  The initial R-value for many of these foams is 7.0 per inch with aged R-value varying depending on manufacturer.


Thermal & Ignition Barrier:

DC-315 Paint to Protect
DC315 Paint to Protect applies as easy as regular latex paint and being water-based it cleans up in a snap. This product is designed for use on interior polyurethane foam surfaces.

  1. Satisfies IBC code compliance for “15 Minute Thermal Barriers”
  2. Low emitting material in the Collaborative for High Performance Schools (CHPS) rating system
  3. Passed strict EPA – VOC and AMQD tests
  4. Non Toxic, Low Vapors, Low VOC less than 50 making DC315 a Green Product

As a Thermal Barrier:

  1. Icynene LD-C-50® -   DC 315 @20 wet mils. (13 dry mils)
  2. Icynene MD-C-200™ - DC 315 @22 wet mils. (14 dry mils)

As an Ignition Barrier:

  1. Icynene LD-C-50® - DC 315 @ 4 wet mils. (3 dry mils)
  2. Icynene LD-R-50® - DC 315 @ 8 wet mils.

(link to product spec, MSDS, ESR)


Infrared Thermography

Infrared Thermography scans are performed with a specialized camera from the inside or outside of a building to detect heat loss and air leakage in the building envelope.  March & Martin performs a scan to check for the effectiveness of insulation (or lack thereof) in the building construction.  We use Infrared Thermography to detect where insulation is needed within a building.  When insulating a “drill & fill” project where the jobsite has finished walls, we use the scans for quality control to make sure there are no voids or air pockets within the closed, non-visible area we are insulating.



Don't have Adobe PDF Reader? Click here: Adobe